Almost there!
Loading website!
Product Code: MEZ Features: Economically priced, excellent hiding power, matt finish CEILING PAINT is a water based emulsion paint for interior and exterior use on plaster, concrete, fibre cement and Cellotex with a high hiding power. This product was especially developed for housing schemes, factories ect., where White colour high hiding is important. PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry 20 minutes Drying Times - Hard Dry 2 hours Over coating Time 6 hours Recommended number of coats 2 - Coverage +/- 7 m² / Ltr Surface Apperance Matt - Cleaning Solvent Water - Shelf Life 6 months Available Colours White Only - Unit Sizes and Weights 20 Ltr = 32.6kg, 5 Ltr = 7.7kg, 1 Ltr = 1.6kg Ltr = kg SUBSTRATE SEALER / FIRST COATER UNDERCOAT, FIRST COATER Mineral or Fiber Cement Substrate - New One coat Plater Primer (MCE-1) N/A Mineral or Fiber Cement Substrate - Previously coated * Prepare as below N/A Celloted - New N/A N/A Celloted - Previously coated ** Prepare as below N/A Previously coated*mineral surface or fiber cement Poor condition: Remove existing paint completely. Make sure plaster or concrete surface is in good condition. Continue as for new mineral substrate or Fiber Cement substrate. Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with FLEX FILL (MXRP-2) or POWDER FILL (MXF-2). After drying seal POWDER FILL (MXF-2) with SEALER (MB-30). Previously coated** Cellotex Remove poorly adhering paint and sand down glossy surfaces. Make sure surface is clean and dry. Apply 2 coats CEILING PAINT (EZ-1) with a sheepskin roller. NB: Always use a sealer and / or primer, before applying PVA ALL IN ONE. For sealer and filler application instructions, see relevant data sheets. Remember - a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact. ...
Product Code: MET Features: Natural Cementations look, Non-patchy even finish, Long lasting / permeable, Ultraviolet- and alkali resistance, User friendly MEDIUM TEX is creating a natural cementatious finish on exterior and interior walls. To be applied with a lamb wool roller or block brush, depending on desired pattern. PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry 30 minutes Drying Times - Hard Dry 2 hours Over coating Time 4 hours Recommended number of coats 1 Prime Coat and 1 to 2 Topcoats - Coverage 5 m² / Ltr Surface Apperance Fine texture, cementatious matt - Cleaning Solvent Water - Shelf Life 6 months Available Colours See Colour card and white - Unit Sizes and Weights 20 Ltr = 32.9kg, 5 Ltr = 8.3kg, 1 Ltr = 1.7kg Ltr = kg SUBSTRATE SEALER / FIRST COATER UNDERCOAT, FIRST COATER Mineral Substrate - New 1 coat MB-20 N/A Mineral Substrate - Previously coated * Prepare as below N/A Previously coated* surface in good condition Sand down glossy surfaces. Touch up holes and cracks with FLEX FILL (MXRP-2) or POWDER FILL (MXF-2). Seal POWDER FILL (MXF-2) with SEALER (MB-30). Make sure surface is clean and dry. Previously coated* surface in poor condition: Remove existing paint. Apply with 2 coats MEDIUM TEX (MET) with a lamb wool roller and if desired, immediately drag with block brush for pattern. NB: Due to the surface texture of MEDIUM TEX, touch-up areas will appear different in colour, due to texture. It is therefore advisable to paint the surface from joint to joint or corner to corner. For application on surfaces, other than above, please contact our sales department (Tel: (061) 22 7050) or the technical department (Tel: (061) 22 7773). Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water! Ventilation Ensure adequate ventilated application area! Spillages Soak up with sand or soil. Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact. Keep away from open flames. ...
Product Code: MEK Features: Good hiding power, Cleanable, Lightfast PVA ALL IN ONE is good quality emulsion paint with good clean-ability, formulated for interior and exterior use on plaster and concrete substrates. PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry 20 minutes Drying Times - Hard Dry 2 hours Over coating Time 6 hours Recommended number of coats 2 - Coverage 7 to 8 m² / Ltr Surface Apperance Slight Sheen - Cleaning Solvent Water - Shelf Life 6 months Available Colours Whilte, Other Colours available on request - Unit Sizes and Weights 20 Ltr = 32.6kg, 5 Ltr = 7.7kg, 1 Ltr = 1.6kg Ltr = kg SUBSTRATE SEALER / FIRST COATER UNDERCOAT, FIRST COATER Mineral Substrate - New Plaster Primer (MCE-1) N/A Mineral Substrate - Previously coated * Prepare as below N/A Previously coated* surface Poor condition: Remove existing paint completely, and continue as for new mineral substrate. Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with FLEX FILL (MXRP-2) (interior) or POWDER FILL (MXF-2) (exterior). After drying seal POWDER FILL (MXF-2) with SEALER (MB-30). Apply 2 coats PVA ALL IN ONE (MEK-) with a sheepskin roller. NB: Always use a sealer and / or primer, before applying PVA ALL IN ONE. For sealer and filler application instructions, see relevant data sheets. Remember - a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact. ...
Product Code: MEAG Features: Hard Wearing, Fully Cleanable, UV Resistent PVA GRADE 1 is a superior quality, pure Acrylic emulsion paint with excellent clean ability for interior and exterior use, providing an exclusive and durable finish. Suitable for use on clean galvanized iron, suitable primed steel, plaster and concrete, as well as for cool-rooms, schools and kitchens ect. PROPERTIES DATA UNITS Resin Type Pure Acrylic - Drying Times - Touch Dry 20 Minutes Drying Times - Hard Dry 2 Hours Over coating Time 6 Hours Recommended number of coats 2 - Coverage 7 to 8 m² / Ltr Surface Apperance Sheen - Cleaning Solvent Water - Shelf Life 6 Months Months Available Colours Whilte, Other colours on request - Unit Sizes and Weights 20 Ltr = 25.7kg, 5 Ltr = 7kg, 1Ltr = 1.4kg Ltr = kg SUBSTRATE CLEANER SEALER / FIRST COAT PRIMER Mineral Substrate - New N/A One coat Plaster Prime (MCE-1) N/A Mineral Substrate - Previously coated * Prepare as below Prepare as below N/A Galvanized Iron - New Clean with Metal Cleaner (MXC-1) N/A Apply 1 coat Metal Primer (MCWP-1) Galvanized Iron - Previously coated ** Prepare as below N/A Prepare as below Steel - New Clean with Metal Cleaner (MXC-1) N/A Apply 1 coat Metal Primer (MCWP-1) Steel - Previously coated *** Prepare as below N/A Prepare as below Previously coated* mineral surface Poor condition: Remove existing paint completely, and continue as for new mineral substrate. Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with FLEX FILL (MXRP-2). Leave to dry. Previously coated** galvanized iron Poor condition: Remove existing paint completely, and continue as for new galvanized iron. Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Previously coated*** steel Poor condition: Remove existing paint completely, and continue as for new steel. Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch in bare areas with METAL PRIMER (MCWP-1). Apply 2 coats PVA GRADE 1 (MEAG) with a sheepskin roller, brush or via spraying. NB: Always use a sealer and / or primer, before applying PVA GRADE 1. For sealer and filler application instructions, see relevant data sheets. Remember - a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact. ...
Product Code: MEL Features: Good hiding power, cleanable, lightfast PVA GRADE 2 is high quality emulsion paint with good clean-ability, formulated for interior and exterior use on plaster and concrete substrates. PROPERTIES DATA UNITS Resin Type Pure Acrylic - Drying Times - Touch Dry 20 Minutes Drying Times - Hard Dry 2 Hours Over coating Time 6 Hours Recommended number of coats 2 - Coverage 7 to 8 m² / Ltr Surface Apperance Slight Sheen - Cleaning Solvent Water - Shelf Life 6 Months Available Colours Whilte, Other colours on request - Unit Sizes and Weights 20 Ltr = 32.6kg, 5 Ltr = 7.7kg, 1Ltr = 1.6kg Ltr = kg SUBSTRATE SEALER / FIRST COATER UNDERCOAT, FIRST COATER Mineral Substrate - New Plaster Primer (MCE-1) N/A Mineral Substrate - Previously coated * Prepare as below N/A Previously coated* surface Poor condition: Remove existing paint completely, and continue as for new mineral substrate. Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with FLEX FILL (MXRP-2) (interior) or POWDER FILL (MXF-2) (exterior). After drying seal POWDER FILL (MXF-2) with SEALER (MB-30). Apply 2 coats PVA GRADE 2 (MEL-) with a sheepskin roller. NB: Always use a sealer and / or primer, before applying PVA ALL IN ONE. For sealer and filler application instructions, see relevant data sheets. Remember - a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact. ...
Product Code: ME0 Features: Economically priced, Good hiding power, Cleanable, Matt Finish PVA GRADE 3 is a water based emulsion paint for interior and exterior use on plaster, concrete, fibre cement and Cellotex with good durability. Improved formula for mixing in pastel and deep colours with better dry hiding. PROPERTIES DATA UNITS Resin Type Acrylic - Drying Times - Touch Dry 20 minutes Drying Times - Hard Dry 2 hours Over coating Time 6 hours Recommended number of coats 2 - Coverage +/- 7 m² / Ltr Surface Apperance Matt - Cleaning Solvent Water - Shelf Life 6 months Available Colours Whilte, Other Colours available on request - Unit Sizes and Weights 20 Ltr = 32.6kg, 5 Ltr = 7.7kg, 1 Ltr = 1.6kg Ltr = kg SUBSTRATE SEALER / FIRST COATER UNDERCOAT, FIRST COATER Mineral Substrate - New Plaster Primer (MCE-1) N/A Mineral Substrate - Previously coated * Prepare as below N/A Cellotex - New One coat Sealer (MB-30) N/A Cellotext - Previous coated ** Prepare as below N/A Previously coated*mineral surface or fiber cement Poor condition: Remove existing paint completely. Make sure plaster or concrete surface is in good condition. Continue as for new mineral substrate or Fiber Cement substrate. Good condition: Sand down glossy surfaces, ensure surface is clean and dry. Poorly adhering, or defective paint must be removed. Touch up holes and cracks with FLEX FILL (MXRP-2) (interior) or POWDER FILL (MXF-2) (exterior). After drying seal POWDER FILL (MXF-2) with SEALER (MB-30). Previously coated** Cellotex Remove poorly adhering paint and sand down glossy surfaces. Make sure surface is clean and dry. Apply 2 coats PVA GRADE 3 with a sheepskin roller. NB: Always use a sealer and / or primer, before applying PVA ALL IN ONE. For sealer and filler application instructions, see relevant data sheets. Remember - a system is only as good as the substrate. For application surfaces, other than above, please contact our sales department. Gloves X Mask - Goggles X Swallowed Rinse mouth with water. Give water to drink. Seek medical attention! Eye Contact Rinse eyes with water and seek medical attention! Skin Contact Immediately wash skin with soap and water. Ventilation Ensure adequate ventilated application area. Spillages Prevent runn off into drains or water ways. Storage Keep container tightly closed. Store in cool, dry place out of direct sunlight Flammable Not flammable. Always keep product out of reach of children. Do not ingest. Avoid eye contact. ...